Please use this identifier to cite or link to this item: https://hdl.handle.net/20.500.14279/9007
DC FieldValueLanguage
dc.contributor.authorRikkou-Kalourkoti, Maria-
dc.contributor.authorKitiri, Elina-
dc.contributor.authorPatrickios, Costas S.-
dc.contributor.authorLeontidis, Epameinondas-
dc.contributor.authorConstantinou, Marios-
dc.contributor.authorConstantinides, Georgios-
dc.contributor.authorZhang, Xiaojun-
dc.contributor.authorPapadakis, Christine M.-
dc.contributor.otherΚωνσταντίνου, Μάριος-
dc.contributor.otherΚωνσταντινίδης, Γεώργιος-
dc.date.accessioned2017-01-12T06:24:23Z-
dc.date.available2017-01-12T06:24:23Z-
dc.date.issued2016-03-09-
dc.identifier.citationMacromolecules, 2016, vol. 49, no. 5, pp. 1731–1742en_US
dc.identifier.issn15205835-
dc.identifier.urihttps://hdl.handle.net/20.500.14279/9007-
dc.description.abstractThis study presents the preparation and characterization of double networks (DN) based on a first amphiphilic polymethacrylate conetwork (APCN) and a second polyacrylamide network. The APCN first network comprised interconnected "in-out" star copolymers of 2-(dimethylamino)ethyl methacrylate (DMAEMA, hydrophilic ionizable monomer) and 2-ethylhexyl methacrylate (EHMA, hydrophobic comonomer) or lauryl methacrylate (LauMA, second hydrophobic comonomer), synthesized using group transfer polymerization, following one-pot, sequential, monomer, and hydrophobic cross-linker (ethylene glycol dimethacrylate, EGDMA) additions. The second network was prepared by the aqueous photopolymerization of acrylamide (AAm) at two different concentrations, 2 and 5 M, and N,N′-methylenebis(acrylamide) cross-linker in the presence of the fully ionized (via HCl addition) APCN. After synthesis, all DNs and single (first and second) (co)networks, equilibrium-swollen in water, were characterized in terms of their mechanical properties in compression. The DNs exhibited improved mechanical properties (stress and strain at break, and elastic modulus) compared to the corresponding single networks. Better reinforcement was achieved in the DNs whose APCN first networks bore a lower hydrophobic content and whose hydrophobic monomer was EHMA rather than LauMA. The best DN exhibited stress at break above 8 MPa and strain at break nearly 80%, close to the values of the best DNs in the literature. Nanoindentation studies were also performed on selected DNs which proved again the enhanced mechanical properties of the present DNs, manifested as high resistance to penetration and low creep displacement. Small-angle X-ray scattering (SAXS) indicated a broad correlation peak for all APCN first networks, suggestive of microphase separation with short-range order, arising from the presence of the hydrophobic segments. The single correlation peak was preserved in the SAXS profiles of the DNs, which was, however, shifted to lower q-values, consistent with further network swelling. Despite the SAXS evidence for only weak phase separation on the nanoscale in the DNs, half of the water-swollen DNs (the ones with a 5 M AAm concentration in the second network) exhibited strong birefringence which probably arose from the stretching of the charged DMAEMA segments rather than the presence of anisotropic nanophases.en_US
dc.formatpdfen_US
dc.language.isoenen_US
dc.relation.ispartofMacromoleculesen_US
dc.rights© American Chemical Societyen_US
dc.subjectDouble network (DN)en_US
dc.subjectAmphiphilic polymethacrylate conetwork (APCN)en_US
dc.titleDouble Networks Based on Amphiphilic Cross-Linked Star Block Copolymer First Conetworks and Randomly Cross-Linked Hydrophilic Second Networksen_US
dc.typeArticleen_US
dc.collaborationCyprus University of Technologyen_US
dc.collaborationUniversity of Cyprusen_US
dc.collaborationTechnische Universität Münchenen_US
dc.subject.categoryMechanical Engineeringen_US
dc.journalsSubscriptionen_US
dc.countryCyprusen_US
dc.countryGermanyen_US
dc.subject.fieldEngineering and Technologyen_US
dc.publicationPeer Revieweden_US
dc.identifier.doi10.1021/acs.macromol.5b02490en_US
dc.relation.issue5en_US
dc.relation.volume49en_US
cut.common.academicyear2015-2016en_US
dc.identifier.spage1731en_US
dc.identifier.epage1742en_US
item.fulltextNo Fulltext-
item.cerifentitytypePublications-
item.grantfulltextnone-
item.openairecristypehttp://purl.org/coar/resource_type/c_6501-
item.openairetypearticle-
item.languageiso639-1en-
crisitem.journal.journalissn1520-5835-
crisitem.journal.publisherAmerican Chemical Society-
crisitem.author.deptDepartment of Mechanical Engineering and Materials Science and Engineering-
crisitem.author.facultyFaculty of Engineering and Technology-
crisitem.author.orcid0000-0003-1979-5176-
crisitem.author.parentorgFaculty of Engineering and Technology-
Appears in Collections:Άρθρα/Articles
CORE Recommender
Show simple item record

SCOPUSTM   
Citations

34
checked on Nov 9, 2023

WEB OF SCIENCETM
Citations 50

33
Last Week
0
Last month
1
checked on Oct 29, 2023

Page view(s) 50

361
Last Week
1
Last month
8
checked on May 9, 2024

Google ScholarTM

Check

Altmetric


Items in KTISIS are protected by copyright, with all rights reserved, unless otherwise indicated.